 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Circa 1933 Schaublin SV12 showing, clearly, the rack (for lever feed) machined into the side of the intermediate head plate
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Accessory No. 201: Swivelling No. 4 Morse vertical head - 90° in each direction from upright- but unfortunately without a quill feed. Reduction bushes were available to accept W20 collets and 1, 2 and 3 Morse taper shanks.
The internal construction of the head was identical to the horizontal type
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Accessory No. 12/747: Slotting head - inclinable 90° each side of vertical and with its stroke variable between 0 and 46 mm. Six rates of stroke were provided of 50, 75, 135, 210, 335 and 525 per minute.
|
|
|
|
|
|
|
 |
|
|
|
|
|
Longitudinal section through the horizontal head. The internal arrangement of the vertical was identical
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Cross section through the horizontal head showing the 2-step pulley and bevel gear drive
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Dividing headstock consisting of: Accessory No. 12/17 fixed quill holder; 12/102 Quill (with a threaded-nose spindle able to take W20 collets, a collet draw bar, a spindle-nose protector and a male centre); 12/110 Dividing plate; 12/108 Pawl and spring and 12/20 Tailstock. The centre height was 90 mm, the quill holder had a 50 mm bore and, fitted with a tailstock, the unit could hold 250 mm between centres. Supplied was a 60-notch plate with others available to order.
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Accessory No. 12/82: Dividing head: supplied with four plates
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Accessory No. 12/38: Rectangular table 450 x 200 mm with four T-slots. The vertical head is fitted with a precision boring head
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Accessory No. 10: Semi-circular table with saddle attachment. The T-slot was on a 162 mm radius and the table (a replica of the Schaublin 102 lathe bed) 296 mm long
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Circa 1933 Schaublin SV12 with the No. 10: Semi-circular table and saddle attachment carrying a headstock from either a 90 or 102 lathe.
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Accessory No. 12/21: Inclinable quill holder with division plate. Equipped with a 50 mm bore this unit was also available with worm and wheel indexing and could take the same fittings as the fixed unit
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Inclinable quill holder fitted with a simple indexing wheel
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
Accessory No. 14E: Inclinable and tilting (universal) table 300 x 160 mm with two 11 mm T-slots on 50 mm spacing
|
|
|
|
|
|
|
|
|
|
|
|
|
|